|
Admin Password:
|
(purposely
not displayed for security protection)
|
|
FXS
Port
:
|
|
|
SIP Server:
|
(Use only if DNS Configured
else USE IP 216.109.159.100)
|
|
Outbound
Proxy:
|
(Use only if DNS Configured
else USE IP )
|
|
SIP User ID:
|
(Use Account Generated on
Smart )
|
|
Authenticate
ID:
|
(Use Account Generated on Smart
)
|
|
Authenticate
Password:
|
( Use Password Generated for
Account on Smart )
|
|
Name:
|
(optional, e.g.,
John Doe)
|
|
Register
Expiration:
|
(If not set Device will
loose registration after 5 Minutes)
|
|
local SIP
port:
|
|
|
local RTP
port:
|
(1024-65535,
default 5004)
|
|
Enable Call Features:
|
No Yes (Disable Call features)
|
|
Send DTMF:
|
in-audio via
RTP (RFC2833) via
SIP INFO
|
|
DTMF Payload
Type:
|
|
|
|
|
FXO
Port
:
|
|
|
SIP Server:
|
(Use only if DNS Configured
else USE IP 216.109.159.100)
|
|
Outbound
Proxy:
|
(Use only if DNS Configured
else USE IP )
|
|
SIP User ID:
|
(Use Account Generated on
Smart )
|
|
Authenticate
ID:
|
(Use Account Generated on
Smart )
|
|
Authenticate
Password:
|
( Use Password Generated for
Account on Smart )
|
|
Name:
|
(optional,
e.g., John Doe)
|
|
Register
Expiration:
|
(If not set Device will
loose registration after 5 Minutes)
|
|
local SIP
port:
|
|
|
local RTP
port:
|
(1024-65535,
default 5008)
|
|
Enable Call Features:
|
No
Yes
(Disable Call features)
|
|
Send DTMF:
|
in-audio
via RTP (RFC2833)
via SIP INFO
|
|
DTMF Payload
Type:
|
|
|
Number of
Rings:
|
(Change to 2 Rings )
|
|
|
|
General Misc. Settings:
|
|
|
Preferred
Vocoder:
(in listed order)
|
choice 1: (Set First Codec)
choice 2: (Set Second Codec)
choice 3:
choice 4:
choice 5:
choice 6: (Set last Codec)
|
|
Voice Frames
per TX:
|
( 30 Frames )
|
|
G723 rate:
|
6.3kbps
encoding rate 5.3kbps
encoding rate
|
|
iLBC frame
size:
|
20ms
30ms
|
|
iLBC payload
type:
|
(between
96 and 127, default is 97)
|
|
Silence
Suppression:
|
No
Yes
|
|
SIP
Registration:
|
Yes
No
|
|
Unregister On
Reboot:
|
Yes
No
|
|
Layer 3 QoS:
|
(Diff-Serv
or Precedence value)
|
|
Layer 2 QoS:
|
802.1Q/VLAN Tag
802.1p priority value (0-7)
|
|
Use DNS SRV:
|
No
Yes
|
|
User ID is phone
number:
|
No Yes
|
|
Early Dial:
|
No
Yes (use
"Yes" only if proxy supports 484 response)
|
|
Dial Plan
Prefix:
|
(this
prefix string is added to each dialed number)
|
|
No Key Entry
Timeout:
|
(in
seconds, default is 4 seconds)
|
|
Use # as Dial
Key:
|
No
Yes
(if set to Yes, "#" will function as the "(Re-)Dial"
key)
|
|
Use random
port:
|
No
Yes
|
|
NAT Traversal:
|
No
Yes, STUN server is:
|
|
keep-alive
interval:
|
(in
seconds, default 20 seconds)
|
|
Use NAT IP
|
(if
specified, this IP address is used in SIP/SDP message)
|
|
Proxy-Require:
|
(if
specified, the content will appear in Proxy-Require header)
|
|
TFTP Upgrade
Server:
|
.
. .
(for remote software
upgrade and configuration)
|
|
SUBSCRIBE for
MWI:
|
No,
do not send SUBSCRIBE for Message Waiting Indication
Yes, send periodical
SUBSCRIBE for Message Waiting Indication
|
|
Offhook
Auto-Dial:
|
(User
ID/extension to dial automatically when offhook)
|
|
Send Flash
Event:
|
No
Yes
(Flash will be sent as a DTMF event if set to Yes)
|
|
FXS Impedance:
|
|
|
Caller ID
Scheme:
|
|
|
Onhook
Voltage:
|
|
|
Disable
Call-Waiting:
|
No
Yes
|
|
Polarity
Reversal:
|
No
Yes
(reverse polarity upon call establishment and termination)
|
|
NTP Server:
|
(URI
or IP address)
|
|
Send Anonymous:
|
No
Yes
(caller ID will be blocked if set to Yes)
|
|
Lock keypad
update:
|
No
Yes
(configuration update via keypad is disabled if set to Yes)
|
|
WAN side http
access:
|
No
Yes
(WAN side access to http server will be rejected if set to No)
|
|
PSTN access
code:
|
(key
pattern to use the PSTN line, default is "*00")
|
|
Route Call to
PSTN:
|
outbound calls will be routed to PSTN port when
dialed digits match one of the following:
|
|
Forward to
PSTN:
|
(VoIP
calls will be forwarded to the specified PSTN number)
|
|
Forward to
VoIP:
|
(PSTN
calls will be forwarded to the specified VoIP number)
|
|
|